Star Wars Roleplay: Chaos

Register a free account today to become a member! Once signed in, you'll be able to participate on this site by adding your own topics and posts, as well as connect with other members through your own private inbox!

Approved Tech Lord Ajihad's Assassin Armor

Status
Not open for further replies.

4e416b037e1d3208f64029eb885c774c.jpg

Image Source: https://s-media-cache-ak0.pinimg.com/736x/4e/41/6b/4e416b037e1d3208f64029eb885c774c.jpg

Intent: A personal set of armor for Lord Ajihad
Development Thread: Phrik, Laminanium
Manufacturer: Mystic Tekk
Model: Mk. 1
Affiliation: Lord Ajihad
Modularity: Colors, padding, other such minor details
Production: Production: Unique

Classification: Anti-Weapon
Weight: 17 kg
Quality: 8

Materials: Alchemized Phrik/Laminanium, anti-ballistics materials, Adegan Synthweave lining, active camouflage unit, Terentatek leather, Specter gloss
Special Features:
  • Rebreather/comm unit
  • Mask can turn into face shield to make suit airtight
  • Phrik adds lightsaber resistance
  • Laminanium heals the armor
  • Anti-ballistics layer reduces blunt impacts, slugs, etc.
  • Alchemized layer prevents others from looking under it with neither the force nor technology
  • Can turn near-invisible with active camo
  • Terentatek leather helps against mentalism
  • Climate control
  • Body temperature concealment

Description: Until now, the assassin Lord Ajihad never really had a good set of armor. He spent quite some time collecting rare and powerful materials for a specialized suit, and is just now putting it all to good use.


He took a base set of Sith Assassin armor and stripped it down, leaving some partial aspects of the personal stealth unit and terentatek leather intact. He replaced the outer layer with a mixture of alchemized Phrik and Laminanium weave. The alchemization makes it so that through the force, technology, or other such means anything concealed under the armor may not be detected. It was backed with a layer of solid ballistic protection, while the innermost layer was lined with Adegan synthweave.


The gauntlets constituted of of Phrik/Laminanium plating rather than weave so punches would be more effective. Small holes were made in the knuckle area to allow Ajihad's fighting claws to emerge.


Every open area of the suit was adjusted so on command, the entire thing can seal up and become airtight. With the right equipment, this will allow the wearer to survive for a short period of time in a vacuum.


Instead of venturing down the path of most assassins creating a personal stealth field, Ajihad did something a little different. Using a high-tech sensory array based off of that of the old stealth system, he created an active camouflage system. Instead of projecting a field around the user that distorts and bends light rays around them, this system simply projects the user's surroundings onto the suit. An advantage to this is that stealth generators are commonly used and many have found ways to bypass them, while active camo is less used and harder to manipulate. A disadvantage is that it is easier to detect when one is moving around at any decent speed, causing visible distortions in the air.


Primary Submissions: Sith Assassin Armor, Specter Gloss
 

ADM. Reshmar

Directorate Officer Fleet Admiral SJC 3rd Fleet
RESEARCH REVIEW
-----
Star Wars Canon:
Pending initial review
------
Starwars Chaos:
Pending initial review
------
WITHOUT DEV THREADS
Pending initial review
------
WITH DEV THREADS
Pending Initial review
------
SUGGESTIONS
Pending Inital review
 

ADM. Reshmar

Directorate Officer Fleet Admiral SJC 3rd Fleet
[member="Lord Ajihad"]
OK so some of this development will not work
I will have to dig through it all and see which threads can be used and which cannot
For sure the phrik thread cannot be used for this as you have already used it for another submission
I will figure it all out and post back later today
 
[member="Reshmar"]

Not going to lie, totally forgot about that lightsaber :p

However, the thread did specify a decent amount of Phrik was found, and only a small amount would have been used to make a lightsaber hilt. I would assume there would be enough remaining to make a single suit of armor?

But I understand the factory works off of the amount of posts put into a thread, so maybe 10 posts is only enough for a small lightsaber hilt?
 

ADM. Reshmar

Directorate Officer Fleet Admiral SJC 3rd Fleet
[member="Lord Ajihad"]
Ok since it was a hilt and they were both unique I figure it will be cool to use it for both. But that thread can not be used for anything else.
 
[member="Reshmar"]

That's awesome, thanks for that!

So the Phrik is woven like armorweave. It's much more cloth like than mesh with a higher general quality of armor. Laminanium also allows the armor to self-repair.

UNLESS I misunderstand and a self-repairing function wouldn't affect the quality of an armor (as I took the Laminanium into account when giving the armor it's quality). If not, then what number would you recommend I lower this to? 7 or 8 I'm guessing?
 

ADM. Reshmar

Directorate Officer Fleet Admiral SJC 3rd Fleet
[member="Lord Ajihad"] It will repair it but not increase its quality for defense against stuff. It just repairs it once it is damaged. In the long run it helps but not for defense against a specific attack.

So since the personnel stealth generator is restricted technology. You will have to do the development for it yourself. The previous development for the sith assassin armor can not be carried into this submission. This is basically a new submission.

Also remove the development thread for the Terentatek leather also since you had no part in the thread.

So do a development thread for the restricted personnel cloaking and make the quality 8
 

ADM. Reshmar

Directorate Officer Fleet Admiral SJC 3rd Fleet
[member="Lord Ajihad"]
Stealth tech requires development, but since this is unique and you have more than enough dev in the other threads for the restricted materials, I will count that extra towards the stealth tech.
 
Status
Not open for further replies.

Users who are viewing this thread

Top Bottom